ASTM C1090 PDF

Faeshakar ASTM C This approach provided more simplicity in the execution of the test, rather than using a projector lamp, magnifying lens, and indicator charts as described in ASTM C see figure The laser approach has asm compared with the original setup, and similar results were obtained. Historical Version s — view previous versions of standard. Testing of shrinkage for concrete — grout. Link to Active This link will always route to the current Active version of the standard. After removal, the thickness of the glass plate was measured with a caliper at ast points of contact between the glass plate and the micrometer.

Author:Voodoorisar Fern
Country:New Zealand
Language:English (Spanish)
Genre:Education
Published (Last):16 June 2005
Pages:332
PDF File Size:8.43 Mb
ePub File Size:14.76 Mb
ISBN:728-7-96583-449-8
Downloads:7571
Price:Free* [*Free Regsitration Required]
Uploader:Bataxe



Gasar An exception is made when the options described in the section on test conditions are exercised. Combining values from the two systems may result in non-conformance with the standard. Sieve size is identified by its standard c in Specification E The glass plate was removed from the top of the test specimen after 24 h. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size.

Two cylindrical specimens with the same dimensions as those used for the ASTM C test method were prepared in which the change in height was measured at four points on the top surface of the specimens using a micrometer in accordance with ASTM C at 1, 3, 7, 14, and 28 d see figure For cementitious grouts, saturate the surface up to SSD.

The height change results in both test methods are expressed in terms of percentage increase or decrease of the original specimen height. This thickness was then added to the four-reading initial measurement. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Testing of shrinkage for concrete — grout.

The height change of a 3-inch mm -diameter by 6-inch mm -tall cylindrical specimen was measured in accordance with ASTM C Historical Version s — view previous versions of standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

After removal, the thickness of the glass plate was measured with a caliper at the points of contact between the glass plate qstm the micrometer. Newer Post Older Post Home. ASTM C Standard This approach provided more simplicity in the execution of the test, rather than using a projector lamp, magnifying lens, and indicator charts as described in ASTM C see figure The laser approach has been compared with the original setup, and similar results were obtained.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. These test methods cover procedures for assessing the adhesion of coating films to metallic substrates by applying and removing pressure-s Link to Active This link will always route to the current Active version of the standard. The degree of restraint varies with the mixture viscosity and c of hardening.

Though not recommended by the ASTM standards, and in order to provide the lowest friction possible, an acetate sheet was used in between the test specimen and the mold. Related Posts

74LS145 DATASHEET PDF

Popular Publishers

The height change results in both test methods are expressed in terms of percentage increase or decrease of the original specimen height. It is the responsibility of the user of this standard to establish appropriate safety and health adtm and determine the applicability of regulatory limitations prior to use. These test methods cover procedures for assessing the adhesion of coating films to metallic substrates by applying and removing pressure-s Newer Post Older Post Home. Combining values from the two systems may result in non-conformance with the standard. Though not recommended by the ASTM standards, and in order to provide the lowest friction possible, an acetate sheet was used in between the test specimen and the mold. Some values have only SI units because the inch-pound equivalents are not used in practice. An exception is made when c options described in the section on test conditions are exercised.

EGZAMIN FCE TESTY PDF

ASTM C1090 PDF

An exception is made when the options described in the section on test conditions are exercised. Combining values from the two zstm may result in non-conformance with the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations c to use. Testing of shrinkage for concrete — grout.

CAMION MINERO 793D PDF

ASTM C1090

Gasar An exception is made when the options described in the section on test conditions are exercised. Combining values from the two systems may result in non-conformance with the standard. Sieve size is identified by its standard c in Specification E The glass plate was removed from the top of the test specimen after 24 h. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size.

GO OAHU CARD GUIDEBOOK PDF

.

Related Articles